NEW CONCEPT FOR IMPROVING SOLAR STILL PERFORMANCE BY USING VIBRATORY HARMONIC EFFECT EXPERIMENTAL PREDICTION, PART-1

A new concept of active vibratory solar still is experimentally presented. Firstly, a flexible packed stretched media is installed in the bottom of the basin to increase the efficiency of the still. Secondly, a vibratory harmonic effect is applied. The flexible packed media is formed from stretched helical coiled copper wires, which is considered as a good media for heat absorbing and transferring and as simple thermal storage system. Also, a vibrator (resonator) is installed in the middle of the system structure. The target of using the vibrator is to generate forced vibration to excite the flexible packed media to break the boundary layer and surface tension of the saline water and improve convective heat transfer, and also to excite the condensed polycarbonate glass cover to assist the condensed droplets to slide down before it becomes bigger and possibly falls down in the basin, thus increasing the water vaporization and condensation. The performance is compared with the conventional solar stills (CSS). The vibratory excitation effect is accounted by the new parameter 'vibratory performance gain'. The productivity due to added backed helical wires is found to be 3.4 l/m≤ day, with efficiency of about 35 %, and the productivity with vibration is increased to be 5.8 l/m≤day and the average daily efficiency is about 60%. The nocturnal production ranges are found from 38 to 57 %.


1-INTRODUCTION
It is well known that the water problems, which are either the lack of it or pollution, have become very large in many areas of our planet, especially in deserts, in traditionally dry regions and in modem industrial areas.Moreover, remote areas or islands with low population, where fresh water supply by means of transport is expensive, face the problem of water shortage every day.However, it is for those areas the installation and operation of solar stills seems to be a promising and the most appropriate way to deal with their water problem.In addition, the process include the use of clean, abundant, free and friendly to the environment solar energy, easiness of construction, operation and maintenance of solar stills by local people and concurrence of periods of high sunshine with high water demand.
Numerous studies on solar stills of various designs to increase its productivities and efficiencies have been carried out theoretically and experimentally.These studies include the determination of the dependence of the productivity on weather, the design and operation parameters [1].Solar stills are classified into two groups in terms of energy supply; passive and active.The passive solar stills are conventional solar stills (CSS) which use the solar energy falling on the basin effective area as the only source of thermal energy.However, in the active solar still, extra thermal energy is given to the passive solar still for faster evaporation, and hence increasing productivity.
Increasing the productivity of the solar stills attract many investigators, several techniques are tried and tested in order to satisfy this main target.A technique of floating sponge, Hegazy [2]; as an absorbing media is used to increase the conduction heat transfer of the brine water and hence accelerate the evaporation rate.A modified type of wick type solar still based on the good capillarity of a jute wick is studied by AL-Karafhouli et al. [3], this type is simply a conventional solar still provided with a blackened jute wick floated with a polystyrene sheet.Results showed that the floatingwick type solar still gives higher productivity but it can't resist contamination.This type is developed by Minasian et al. [4] by increasing the cooling effect of the condensing cover.The technique of adding one or more outside condensing chambers to magnify the condensing effect is studied also by Tiwari [7] and E1-Bahi [8] the daily production is increased by 70% and in case of adding a double glass with minimum inclination, [9] and [10], the productivity was in good agreement with what obtained by other authors and the efficiency was increased from 37% to more than 69% when the condenser cover was cooled down.
A multiple effect solar stills is studied by Tanaka et al [5,6], they constructed and tested vertical two and three-effect-type stills with recycling the condensing heat to increase the total amount of distillate and its efficiency.They developed it by adding a heat-pipe solar collector and the still is predicted to produce distilled water with efficiency increased factor of 1.2 -1.6.This technique is developed by adding air blown by Mink et al. [10]; they estimated the effect on the still productivity and found it very promising for enhancing the thermal efficiency, and thus a further increase in the productivity per unit area.
Active solar distillation on the other hand is considered a second type of the used techniques to increase the productivity and efficiency of CSS.Prasad et al. [11] and Phadatare et al. [12] found that when feeding the thermal energy into the basin from external source, it can increase the evaporating surface temperature and can lead to increase the nocturnal production.The first study on nocturnal production was reported by Malik and Tran [13].Voropoulos et al. [14] used hot water tank underneath the absorbing surface working as energy storage tank, they found that the nocturnal production is increased relatively with the total production by 60 % [15][16][17].
Zeinab et al. [18] presented a new active technique by using rotating shaft installed close to the basin water surface to break the boundary layer of the basin water surface together with adding packed thermal layer.The packed layer is installed in the bottom of the basin to increase the efficiency of the still; it is formed from glass balls which are considered a simple thermal storage system.They found that the efficiency of the modified solar desalination system using packed layer was increased by 5 -7.5 %, and by 2.5-5.5 % for the modified one using rotating shaft.
For improving the solar still performance new approaches are highly welcome.An attempt to improve the performance of solar still should include an investigation on the performance of new design configurations.To the best of our knowledge, a vibratory excited flexible packed stretched media installed in the basin has not been investigated.
The objective of this study is to investigate the performance enhancement of a solar still coupled with vibratory excited flexible packed stretched media in two modes of operation.The first mode includes the operation of the still with a flexible packed stretched media installed in the bottom of the basin.For the aim of comparison; in the second mode a vibratory harmonic excitation is applied together with the first mode.In this respect, the article is concerned mainly with the system productivity to evaluate the effect of proposed concept on improving the performance of the solar stills.Also the effect of increasing the thermal storage capacity of the basin brine water on the nocturnal production.
We can summarize the concept technique in the following notes: 1-Installing flexible packed media (stretched helical coiled copper wires) on the bottom of the basin submerged in the brine water.2-Applying forced vibration of very low power to excite the modified absorbing media.3-Increasing the stored energy capacity by increasing the water depth and using good isolation.4-Improving collection process of the condensation.

Solar still station configurations
This active solar still is designed and built in the southern desert area of Saudi Arabia (Wadi El-dwaser, 21.5° latitude and 44° longitude), in the year 2006 to supply distillate water to a battery service center in a large farm.It uses the under ground water as a brine, which is lifted from deep wells.
The system has a double sloped cover of 30° inclination with the horizontal and total effective area of 2.064 m².It is made from coated steal sheets and angles, Figure (1) shows a schematic drawing of the solar still, it is equipped with basin level control valve, which is included inside closed tank.The transparent cover is made from polycarbonate composite sheets of 4 mm thickness partitioned to six segments, three on each side.A tight sealing of the inside enclosure is attained by using silicon rubber past with galvanized bolts for all connections of top cover and basin parts.The basin total height is 70 mm and it has two troughs, one on each side for collecting the distillate, then transferring it to the outside collecting vessels, which are tight closed and located at a shaded spots in the way of natural air ventilation stream.
Helical copper wires are stretched over the basin bottom, as shown in Figure (2).The coil mean diameter is 25 mm and the wire diameter is 1.5 mm, they are blackened as the basin bottom.The average depth of the brine water in the basin is 60 mm, and the total average water mass is about 100 kg.The vibrator is located at the center of the base bottom as shown in Figure (1).It is composed of a rotating disk driven by ac motor, as shown in Figure (3), the disk has an unbalance mass of 30 grams, located at radius of 40 mm.The motor speed is 1500 rpm, so the frequency of the vibration is 25 Hz. and the maximum exiting force is about 29 Newton.The vibration is directed mainly to the vertical direction by using unidirectional elastic supports (rubber constrained layer) underneath the four columns which are carrying the system.The power consumed by the vibrator is about 50 watts, so that the daily electric consumption is about 1.2 KW h.

Fig. (3) Vibrator configuration
The basin outside surface is covered by two layers of foiled glass-wool of total thickness of 40 mm and rested on wooden plates of thickness 25 mm.The solar still is directed to the north-south direction.
The design parameters of the system are: -Effective black area of basin is 2.064 m²; -Net helical coil wires surface area is 6.0 m²; -Coil with a diameter of 25 mm; -Copper wire with a diameter of 1.5 mm; -Density of wire material (copper) is 8890 kg/m³; -The double-sloped angle is 30 deg. horizontally; -The basin height is 70 mm; -The isolation thickness is 40 mm of wool glass of thermal conductivity of Kw.g = 0.038(W/mK).And wood of thickness 25 mm of thermal conductivity 0.04 W/mK; -Vibrator frequency is 25 Hz; -Exciting force is 29 N; -Mass of the station is 150 kg; -Mass of brine water is 100 kg; -Mass of helical coiled wires is 20 kg; -Density of polycarbonate glass sheet is 900 kg/m³.

Experimental measurement procedure
The measurements of the productivities, with and without vibration, of the proposed solar still station are done in the first three weeks by running the vibrator day by day in order to have two consecutive day records at the same climatic conditions, for evaluating the vibratory harmonic effect.These two days (19 th and 20 th of September 2006) are found to have the same climatic conditions.The starting measuring time begins at 6 am and along 24 hours following this time until the ending measuring time at 6 am of the second day, so the quantity of distillate water is measured each six hours, at time hours of 12 pm, 18 pm, 12 0.0 am and 6 am.The solar irradiation distribution is calculated in the day of 20 th September 2006 [19] and [20], for autumn sunny day and the total solar insulation is found to be 22.43 MJ/m²day.

Thermal analysis of the helical wires without vibration
The helical wires are used to assist the desalination process during the sunrise and after the sunset.The target of using it is to increase the distillate water productivity per day.The thermal equations of the helical wires are derived with no vibration and neglecting losses as [18]: The total solar radiation will be where: Subscripts w and b denote to helical wires packing and brine water, respectively.

( ) ( ) b w and ατ ατ
: absorptivity and transmissivity of the helical wires and brine water respectively.t q : total solar insulation per day, MJ/m²day.w b g q q q , , : total solar irradiation absorbed by polycarbonate glass cover, brine water, and helical wires backed layer.The performance of the modified solar desalination system using helical wires is evaluated by the ratio of the energy that utilized in water vaporization in the still for daily distillate water productivity (Wd1, l/m 2 day) to the total input solar energy ( s I , W/ 2 m ) as follows: where:

The vibratory performance gain (helical wires with vibration)
The efficiency the still with vibration applied to the helical wire packing vw η is expressed by the ratio of the energy that utilized for water productivity ( ) that as: ( ) where: v P : The vibrator motor power, W. The value of the VPG may reach more than 1, because the power consumed by the vibrator is not converted to thermal power in the energy balance process, but it works as a catalytic agent to assist the heat transfer process, and hence increasing the rate of vaporization, also assisting the condensed droplets on the polycarbonate covers to slide down easy by breaking the surface tension before it grow up and possibly get lost.
The VPG may be calculated either for each period of the day or as average value per day.

Effect of flexible packed helical wires
The productivity of the solar still with modified helical packed wires is shown in Figure (4); it reached value of 3.4 l/m²day, with efficiency of 35%, as shown in Figure (7).There is a significant increase when compared with productivity of CSS of reference [18] by a ratio of 36%.The figure gives different comparisons with other references [7] and [10] with increasing ratios more than the obtained ratio by reference [18].The peak of performance rate production (PRP) is occurred at time hour 18 (6 pm), as shown in Figure (5).

Effect of harmonically exiting of the system
The effect of modified absorbing surface coupled with harmonically exited vibration on the production rate performance (PRP) is shown in Figure (5).There is a significant increase from 1.3 l/m²h to 2.2 l/m²h with increasing ratio of 69 %, while the accumulated daily productivity is increased, as shown in Figure ( 6) from 3.4 l/m²d to 5.8 l/m²d by increasing ratio of 72 %.The peak of (PRP) is occurred at time hour 24 (12 0.0 am), due to the effect of excitation for utilizing the thermal stored energy.Figure (7) shows the average daily productivity and efficiency through out three weeks and comparisons with helical wires and CSS results of reference [7] which is measured in the same day of the year.
The "Vibratory Performance Gain (VPG) which is defined by equation ( 20) is shown in Figure (8), there is a peak value of 4.   Ef f iciency w ith vib.ef f iciency of CSS, ref [7] Ef f . of Helical w ires Prod.w ith vib.prod. of CSS ref .[7] Fig

Effect of thermal storage
The effect of thermal storage in the basin brine water and helical packed wires on the nocturnal production is shown in Figure (9) with daily distribution of solar insulation on the day of the 20 th of September 2006 in the area of Wadi Eldwaser.It is shown that the nocturnal production is 1.4 l/m²d with percentage of 41 % when operating without vibration and increased to a value of 2.9 liters/m².dwith percentage of 50% when operating with vibration.
The maximum (PRP) performance rate production is found at time hour 18 (6 pm) for the helical packed wires and at time 24 (12 0.0 am) when working with vibration, so that the vibratory excitation extending the nocturnal production period by 6 hours, as shown in Figure (10).The percentage of nocturnal production for three weeks with vibration is shown in Figure (11); its value is ranged as 37 -50%.

5-CONCLUSION
A new concept is used in the present work, it is based on modifying the absorbing surface media by installing stretched helical coiled wires in the basin of the solar still, and this packed layer has a good performance effect when it is excited harmonically.
The excitation of the helical wires is found to have a good effect on the performance of the modified solar still, due to increasing Nusselt Number.Which is magnifying the overall heat transfer coefficient?Also it increase the condensate on the vibrating polycarbonate glass covers.
The productivity of the of the still with added helical wires is found to be 3.8 l/m² day with efficiency of 35 % and increased with vibration to 5.8 l/m²day with efficiency of 60 %.The increasing percentage in the productivity due to the vibratory excitation effect is 72 %.
The productivity of the still with helical wires is 35 % more than the productivity of CSS and when vibration is applied this ratio increases to 132 %.
The effect of vibration is defined by the new parameter 'vibratory performance gain', it was found to be of average value of 2.6 and peak value of 4.4.
The results showed that using this concept is very promising for developing basin-type solar stills with very low investment costs.

Fig. ( 1 )
Fig. (1) Active solar still configurations of helical wires and brine water, respectively.b w m and m : masses of the helical wires and brine water, respectively.b w anda A : surface areas of helical wires and brine water, respectively.
and without vibration.

Fig. ( 4 )
Fig. (4) Effect of packed helical wires on the accumulated daily productivity and comparison with Ref. [7], [10], and [18] 4 at time hour 42 (12 0.0am) and the daily average value is 2.6.The figure indicate that the value of VPG is started from zero at the beginning of the solar time hour (6 am) and increased gradually by a constant rate until it reaches its peak at time hour 24 (12 0.0 am) at mid night.This happened due to the excitation of thermal storage which is increasing the nocturnal production.

Fig
Fig. (9) Solar insulation distribution and productivity